WISCO International

Home Page | Manufacturers | ICOM | IC-F5060/6061 | Quotation Request | Search | E-mail

IC-F5060/IC-F6061
SPECIFICATIONS

General

Frequency range
IC-F5061
IC-F6061

136–174MHz
400–470MHz,
450–512MHz
Number of channels 512 channels/ 128 zones
Channel spacing 12.5/25kHz, 15/30kHz (6.25kHz (option))
PLL channel step 2.5kHz, 3.125kHz
Antenna impedance 50Ω
Operating Temp. range –30°C to +60°C  ( –22°F to +140°F)
Power supply requirement 13.6V DC nominal
Current drain (approx)
Tx
Rx
 
50W/45W 14.0A
Max. audio 1200mA
Stand-by 300mA
Dimensions (W×H×D)
(projections not included)
160×45×150 mm
6516×12532×52932 in
Weight (approx.) 1.31kg; 2.9lb
Transmitter
Output power (approx) 50W (VHF)
45W (UHF)
Max. frequency deviation ±5.0/2.5kHz (Wide/Narrow)
Frequency error ±1.0ppm
Spurious emissions 75dB typ.
FM Hum and Noise 45/40dB typ. (Wide/Narrow)
Adjacent channel power 70/60dB min. (Wide/Narrow)
Audio harmonic distortion 3% typ. (40% deviation)
Modulation limiting 70–100% of Max. deviation
Ext. microphone impedance 600Ω (8-pin modular)
Receiver
Sensitivity (12dB SINAD) 0.25μV typ.
Squelch sensitivity 0.25μV typ. (at threshold)
Adjacent channel selectivity 85/75dB typ. (Wide/Narrow)
Spurious response 90dB typ.
Intermodulation 77dB typ.
Hum and noise ratio 50/45dB typ. (Wide/Narrow)
Audio output power 4W typ. at 10% distortion with a 4Ω load
External speaker connector 2-conductor 3.5 (d) mm (18″) /4Ω
 

Applicable U.S. Military Specifications

The IC-F5061/F6061 and RMK-3 have been tested to and passed the following MIL-STD requirements and strict environmental standards.

Standard MIL 810 C MIL 810 D MIL 810 E MIL 810 F
Method Proc Method Proc Method Proc Method Proc
High Temp. 501.1 I 501.2 I, II 501.3 I, II 501.4 I, II
Low Temp. 502.1 I 502.2 I, II 502.3 I, II 502.4 I, II
Temp. Shock 503.1 I 503.2 I 503.3 I 503.4 I
Rain Blowing* 506.1 I 506.2 I 506.3 I 506.4 I
Rain* 506.1 II 506.2 III 506.3 III 506.4 III
Humidity 507.1 I, II 507.2 II, III 507.3 II, III 507.4
Vibration 514.2 VIII, X 514.3 I 514.4 I 514.5 I
Shock 516.2 I, II, V 516.3 I, IV 516.4 I, IV 516.5 I, IV

* Rain blowing and drip tests were performed on the controller and RMK-3 only.

Measurements made in accordance with EIA-152C/204D, TIA-603. All stated specifications are subject to change without notice or obligation.

Supplied Accessories

  • Hand microphone, HM-148
  • Microphone hanger
  • Key assign stickers
  • DC power cable
  • Mounting bracket kit
 
WISCO International, Inc. - MIAMI, FL U.S.A.
Fax: (954) 370-3997 | E-mail: wiscointl@wiscointl.com

Home Page | Manufacturers | ICOM | IC-F5060/6061 | Quotation Request | Search | E-mail